Skip to main content
Water Damage Assessment & Inspection in Burnaby

Water Damage Assessment & Inspection in Burnaby

Pin meters, a thermal camera, and photos build the Burnaby moisture map, from Heights crawls to hill walk-outs and Metrotown stacks.

Metrotown, Burnaby Heights, Capitol Hill, South Slope, and the rest of Burnaby

Heights bungalows keep their damp under the floorboards. We start a Burnaby inspection with a scan meter on the fir, then a pin meter if the crawl hatch will open. Burnaby Heights and Edmonds still have those low bungalow crawls, cold and often bare at the soil. Capitol Hill and South Slope walk-outs sit in till, so the high reading is usually the uphill wall. Sullivan is flatter, and groundwater shows along the footing after a long rain. Metrotown is concrete, and the wet suite is often the one under a failed line. Kingsway shops add a roof drain or a kitchen line once the street is quiet.

This visit is the inspection. We record rooms, materials, and a category of water, clean supply or dirty drain. Pin meter, scan meter, thermal camera, and photos of every wet edge. The moisture map is the product we leave behind. The sheet you keep lists the rooms, the materials, and a photo of each wet edge.

Burnaby Heights crawl joist moisture map under the bungalow floor

The hatch in a Burnaby Heights bungalow is often a closet panel or a square beside the laundry tub. We scan the fir floor from the room. If the number climbs, we go under with a pin meter on the joists and the sill. Edmonds crawls from those same years get the same order of work.

Photos catch the waterline on the pier blocks and any dark insulation in the bays. Every bay we reach goes on the moisture map with the reading and the material. A supply leak keeps salvage open. Drain water changes the category and what comes out.

Capitol Hill walk-out moisture map along the till side wall

Capitol Hill walk-outs sit in the slope, and South Slope houses on that ridge take water the same way. Rain runs the street and finds the window well or the stair. We meter the uphill wall in a grid, low and high, and we compare it to the downhill side.

A thermal camera shows the cold band where water tracked inside the wall, past the paint. We photograph the well, the stair, and the meter on the panel. Those points become the moisture map. Muddy surface water gets its own category line on the page.

Sullivan flats footing moisture map after groundwater reaches the slab

Sullivan sits on the flats, and water there often comes through the footing once the ground is full. The meter runs the slab edge, the bottom plate, and any swollen baseboard. Groundwater can look clear and still carry silt. We write what we see.

Photos include the outside grade, the downspouts, and the wet line inside. The moisture map marks how far the reading stays high as you walk toward the middle of the room. We note whether the footing was already wet when we arrived. That timing belongs in the file.

Metrotown suite stack moisture map from the concrete unit above

Metrotown suites are concrete, and the water usually enters from the home above or a stack in the wall. We meter the ceiling, the wall under the stain, and the floor if the water travelled. A thermal camera finds a wet band in the gypsum before the paint blisters.

If we cannot enter the suite above, we name it as the likely source and mark it unconfirmed. Photos show the ceiling, the meter, and any drip. The moisture map covers your rooms plus a note on the stack. We note the category. Kingsway shops get the same photos when a roof drain is the inlet.

Questions about water damage assessment & inspection in Burnaby

What will a Burnaby Heights crawl moisture map actually list?

+
It names each joist bay we could reach, the pin reading on the wood, and a photo of the waterline on the piers or the soil. We write whether the inlet looks like a supply leak or water that reached the crawl from a drain. You can forward that page. It is the inspection record, and it stops at what we measured.

Can a thermal camera see wet gypsum in a South Slope walk-out wall?

+
It can show a cold track inside the wall that your hand on the paint will miss. We still confirm with a meter, because a cold pipe can look like a wet bay on the screen. The photo of that screen and the meter reading both go on the moisture map for the uphill wall. That is how a walk-out on this ridge gets documented.

How do you assess a Kingsway shop if the water came from above?

+
We map the shop you can give us: ceiling, walls, floor, and stock that got wet. We name the likely stack or the suite above when the path is clear, and we mark it unconfirmed if the door upstairs stays shut. The category of water is written from what landed in the shop. Photos of the ceiling and the meter go with that note.

Get an Assessment

Tell us what happened in Burnabyand we'll get back to you.

For immediate water emergencies, call (604) 200-3261

Water emergency right now?

(604) 200-3261

Available 24/7

On this page

Water Damage Assessment & Inspection written for Burnaby houses, including Metrotown, Burnaby Heights, Capitol Hill.

All water damage assessment & inspection details
Restoration crew drying a water-damaged home in Burnaby

Ready to Restore Your Property?

Burnaby's Water Damage Restoration
Specialists Are Standing By

Whether you're dealing with a flooded basement, a burst pipe, storm damage, or the aftermath of a sewage backup — our Burnaby restoration company is here to help. Call now to get an assessment and same-day emergency response.

IICRC Certified · Licensed & Insured · Serving Burnaby, BC and all of Metro Vancouver